Baseboard and Crown Molding using the
#J-FK-P set
 |
| Craft Saw & Miter Box |
 |
| EZ Cutter & Sandpaper |
 |
| Hacksaw & Craft Knife |
Installing Baseboard and Crown molding
wallpaper00_lg.jpg
DHTMLGoodies.com
This is the whole #J-FK-P pack (it is also available un-painted)
BaseboardCrown/BaseboardCrown01_lg.jpg
This is the whole #J-FK-P pack (it is also available un-painted)
BaseboardCrown/BaseboardCrown01_lg.jpg
DHTMLGoodies.com
Three different toolsets that can be used for cutting molding
BaseboardCrown/BaseboardCrown02_lg.jpg
Three different toolsets that can be used for cutting molding
BaseboardCrown/BaseboardCrown02_lg.jpg
DHTMLGoodies.com
The Miter Box has a lip on the bottom that hooks on the table edge
BaseboardCrown/BaseboardCrown03_lg.jpg
The Miter Box has a lip on the bottom that hooks on the table edge
BaseboardCrown/BaseboardCrown03_lg.jpg
DHTMLGoodies.com
hold the molding up-side-down for a miter aimed the other direction...
BaseboardCrown/BaseboardCrown06_lg.jpg
hold the molding up-side-down for a miter aimed the other direction...
BaseboardCrown/BaseboardCrown06_lg.jpg
DHTMLGoodies.com
Cut the Front Molding first (the length in back is the same)
BaseboardCrown/BaseboardCrown08_lg.jpg
Cut the Front Molding first (the length in back is the same)
BaseboardCrown/BaseboardCrown08_lg.jpg
DHTMLGoodies.com
The right angled cut (molding is up-side-down)
BaseboardCrown/BaseboardCrown12_lg.jpg
The right angled cut (molding is up-side-down)
BaseboardCrown/BaseboardCrown12_lg.jpg
DHTMLGoodies.com
... but the saw keeps dropping off the cut making it ragged
BaseboardCrown/BaseboardCrown18_lg.jpg
... but the saw keeps dropping off the cut making it ragged
BaseboardCrown/BaseboardCrown18_lg.jpg
DHTMLGoodies.com
The other side molding, mitered and cut to fit
BaseboardCrown/BaseboardCrown21_lg.jpg
The other side molding, mitered and cut to fit
BaseboardCrown/BaseboardCrown21_lg.jpg
DHTMLGoodies.com
Paint the ends of the front baseboard so there's no darkness in the joint
BaseboardCrown/BaseboardCrown23_lg.jpg
Paint the ends of the front baseboard so there's no darkness in the joint
BaseboardCrown/BaseboardCrown23_lg.jpg
DHTMLGoodies.com
Spread light spackle on the end of the side moldings
BaseboardCrown/BaseboardCrown24_lg.jpg
Spread light spackle on the end of the side moldings
BaseboardCrown/BaseboardCrown24_lg.jpg
DHTMLGoodies.com
Spackle fills the corner and squeezes out - clean up with a paintbrush
BaseboardCrown/BaseboardCrown25_lg.jpg
Spackle fills the corner and squeezes out - clean up with a paintbrush
BaseboardCrown/BaseboardCrown25_lg.jpg
DHTMLGoodies.com
Clothespins and weights to keep the baseboard tight while the glue dries
BaseboardCrown/BaseboardCrown27_lg.jpg
Clothespins and weights to keep the baseboard tight while the glue dries
BaseboardCrown/BaseboardCrown27_lg.jpg
DHTMLGoodies.com
Tracing the front of the stairs (away from you in this picture)
BaseboardCrown/BaseboardCrown29_lg.jpg
Tracing the front of the stairs (away from you in this picture)
BaseboardCrown/BaseboardCrown29_lg.jpg
DHTMLGoodies.com
Cut on a cutting board - this is not a Miter Box angle
BaseboardCrown/BaseboardCrown31_lg.jpg
Cut on a cutting board - this is not a Miter Box angle
BaseboardCrown/BaseboardCrown31_lg.jpg
DHTMLGoodies.com
Do not glue in this piece until after installing the stairs
BaseboardCrown/BaseboardCrown32_lg.jpg
Do not glue in this piece until after installing the stairs
BaseboardCrown/BaseboardCrown32_lg.jpg
DHTMLGoodies.com
Do not glue in this piece either if you are going to use landing rails
BaseboardCrown/BaseboardCrown33_lg.jpg
Do not glue in this piece either if you are going to use landing rails
BaseboardCrown/BaseboardCrown33_lg.jpg
DHTMLGoodies.com
Use the taped-together template to cut the attic baseboard
BaseboardCrown/BaseboardCrown41_lg.jpg
Use the taped-together template to cut the attic baseboard
BaseboardCrown/BaseboardCrown41_lg.jpg
